Exactly How to Install a Bath Tub: Set Up an Acrylic Tub and Also Bathtub Surround
Exactly How to Install a Bath Tub: Set Up an Acrylic Tub and Also Bathtub Surround
Blog Article
We have found this post pertaining to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround directly below on the web and figured it made sense to relate it with you on this page.
Installing a tub isn't specifically rocket science, however it does need strong plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old tub with a brand-new one is also a moderately tough task. If the old tub is readily easily accessible, the task can move quickly; if you need to open up a wall surface to remove the old tub as well as place the brand-new bathtub, the task is much harder. In either situation, the task is within a residence handyman's skills, although you will need a helper to move out the old tub as well as set in the new one. Ensure you have qualified yourself for the task as well as are comfortable attempting it. Instead of employing a contractor to take over a halfway-completed project, it is much better to think about utilizing one prior to you start. Chances are you may need a professional plumber to make tube connections.
This short article will assist you set up a brand-new tub in your shower room if you have actually currently gotten a brand-new bathtub and also do not require to alter the plan of your previous water system pipelines.
Your devices as well as material checklist ought to make up the following:
Removing Old Touches
If you need to replace old taps with new ones as a part of your installation, after that the first thing you need to do is separate the water system. After doing so, switch on the faucets to drain pipes any kind of water staying in the system. The process of eliminating the existing taps can be quite bothersome as a result of the limited gain access to that is frequently the case.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the faucets. Have a fabric ready for the remaining water that will certainly originate from the pipes. Once the supply pipelines have actually been eliminated, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning during this procedure. When the taps have been gotten rid of, the holes in the bath/basin will have to be cleansed of any kind of old sealing compound.
Prior to carrying on to fit the new faucets, compare the pipe links on the old taps to the new faucets. If the old taps are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic port to stop damage to the string. One end of the adapter fits on the plastic tail of the tap and the various other end offers a link to the existing supply pipes.
If you require to fit a monobloc, then you will certainly require lowering couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the installing opening in the bath/basin guaranteeing that the washers remain in place in between the tap as well as the sink. Secure the faucet in place with the maker provided backnut. When the tap is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet adapters. The former kind ought to be attached to the tap finishes first, tightening just by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Tub
Utilizing both wood boards under its feet, place the tub in the called for placement. The wooden boards are valuable in equally spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 small points.
The next objective is to make certain that the bathtub is leveled all round. This can be achieved by inspecting the level and also readjusting the feet on the bathtub until the spirit level checks out degree.
To mount faucets, fit the bottom of the furthest versatile tap port to the proper supply pipeline by making a compression sign up with; then do the same for the other tap.
Turn on the supply of water as well as examine all joints and also brand-new pipework for leakages and also tighten them if essential. Fill the bathtub and also check the overflow outlet and the normal outlet for leaks.
Lastly, repair the bath paneling as explained in the producer's instruction manual. Tiling as well as sealing around the tub ought to wait up until the bathtub has been used at least once as this will certainly resolve it right into its last placement.
Planning for the Installment
To start with, the sustaining frame provided with the bath should be fitted (if required) according to the manufacturer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is important to see to it that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets device to avoid stress on the tub.
Fit the versatile tap connectors to the bottom of the two faucets making use of 2 nuts and also olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you use all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be fitted in its final placement.
Tiling Around the Tub
In the area where the bathroom satisfies the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to split a rigid seal, creating the water to permeate the wall in between the bath and the tiling, causing difficulties with moisture and feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your components and installations. They are offered in tubes and also cartridges, as well as are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill up the bath tub with water before securing, to enable the motion experienced when the bathtub is in usage. The sealant can split fairly very early if you do not take into account this motion prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also conveniently available on the marketplace. It is suggested to fit the ceramic tiles making use of water-resistant or water resistant glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our post about A Step-by-Step Guide to Installing a Bathtub. Thank you so much for taking a few minutes to read through our piece. Loved our piece of writing? Please share it. Help another person find it. We love reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Book Appointment Now
Report this page